Storage containers are typical "large-area, thin-wall, high-frequency-use" plastic products. The application of IML (In-Mold Labeling) labels on storage containers demands higher production process requirements than ordinary small containers – the label area is large, the container body has thin walls, and the injection molding cycle is longer. Any issue at any step means the entire panel is scrapped, resulting in losses far greater than for small-label products.
This article systematically analyzes the five most common defects in IML storage container production from four perspectives: label selection, workshop temperature/humidity, injection molding parameters, and ink compatibility – along with their solutions.

Wave-like wrinkles, localized bulges, or indentations appear on the label surface. In severe cases, the label separates from the container surface. This is one of the most common appearance defects in IML production.
Label dimensions do not match the mold
If the label unit length is too long, it exceeds the reserved space, causing the label to "bunch up" inside the mold; if it is too short, it cannot conform fully to the cavity wall, also causing wrinkles. Storage container labels have large areas, so the amplification effect of dimensional deviations is more pronounced.
Insufficient label material extensibility
Film materials, especially those that can stretch and deform, can conform to the curved surfaces of storage container bodies without wrinkling. If a film with excessive rigidity or insufficient extensibility is chosen, wrinkling is likely to occur on large flat or micro-curved container surfaces.
Electrostatic adsorption failure
IML injection molding generally uses electrostatic label attraction, because injection molding pressure is high and vacuum suction can easily be broken through. If electrostatic adsorption is insufficient, the label cannot firmly adhere to the mold cavity wall and is prone to shifting or wrinkling under the high-pressure, high-temperature impact of injection. Electrostatic performance is significantly affected by humidity – fluctuations in workshop humidity directly cause unstable adsorption.
Inadequate film thermoforming
The film must undergo thermoforming treatment before being placed in the mold. Improper temperature control can cause film deformation and increase the rejection rate. The film size should be 0.02-0.03mm smaller per side than the final part size, ensuring easy placement while allowing full expansion during injection.
| Investigation Direction | Specific Measures |
|---|---|
| Label dimensions | Confirm label cutting dimensions precisely match the mold cavity; check unit length stability |
| Label material | Choose a film material with good extensibility; avoid excessive rigidity |
| Electrostatic adsorption | Check if the electrostatic generator is working properly; control workshop humidity at around 50% |
| Film thermoforming | Strictly control thermoforming temperature; film size 0.02-0.03mm smaller per side than the part |
White patches or hazy areas appear on the label area of storage container panels, with the color turning white or grey, creating an obvious color difference from surrounding normal areas. This is often referred to as "blushing" or "stress whitening" in the industry.
Residual stress causing whitening
During demolding, if the draft angle is too small or the mold surface is rough, excessive ejection force creates stress on the product surface. In severe cases, whitening or cracking occurs in stress-concentrated areas. Large flat storage container panels have large surface areas where stress distribution is even more uneven, increasing the risk of whitening.
Uneven wall thickness causing stress concentration
If the wall thickness of storage container panels is uneven – thick areas cool slowly and shrink more – tensile stress is generated at the label-substrate interface, leading to localized whitening. Areas where wall thickness changes are high-risk zones for whitening.
Excessively low mold temperature
Low mold temperature can easily cause product deformation or defects such as white streaks and black spots. For large flat storage containers, localized "cold material" caused by uneven mold temperature is particularly common.
| Investigation Direction | Specific Measures |
|---|---|
| Mold temperature | Increase mold temperature to the recommended range; ensure uniform temperature across all cavity areas |
| Wall thickness design | Check if panel wall thickness is uniform; avoid localized excessive thickness; design smooth transitions at thick-thin junctions |
| Draft angle | Check if draft angle is sufficient (IML products require ≥3°) |
| Injection pressure | Adjust injection pressure and holding pressure to reduce residual stress |
After injection molding, the ink on the label shows diffusion, blurring, or darkening of colors. In severe cases, pattern edges become indistinct and color saturation noticeably decreases.
Insufficient ink adhesion to the film
Poor ink adhesion to the label can easily cause ink contamination of the mold, leading to poor product quality. If ink adhesion to the film is insufficient, the high-temperature, high-pressure environment during injection accelerates ink diffusion and migration.
Insufficient ink heat resistance
The temperature of molten plastic during injection can reach 180-280°C. If the ink's temperature resistance limit is lower than the injection temperature, the ink layer softens at high temperatures, and pigment molecules gain enough energy to move within the film.
Additive migration in ink
When the ink or substrate contains excessive plasticizers or other additives, these additives can dissolve some of the ink's pigments under high temperature or long-term storage conditions, causing them to move within the film.
| Investigation Direction | Specific Measures |
|---|---|
| Ink selection | Choose UV inks – their ink layer strength is higher than solvent-based inks, making them more suitable for in-mold labels |
| Surface tension | Check if material surface tension meets requirements (38 dynes); if not, perform corona treatment |
| Ink testing | Test ink adhesion, scratch resistance, and chemical resistance on the label material before use |
| Additive control | Choose plasticizer additives with low or non-migrating properties; use resins with high softening points as ink binders |
After injection molding, the pattern on the label appears deformed – circles become ellipses, squares become rectangles, text is stretched or compressed. The pattern clearly does not match the design artwork.
Film stretched and deformed inside the mold
After the IML film is placed in the mold, if the stretch ratio during thermoforming is not properly controlled, or if the melt flow during injection is uneven, the film will be stretched, causing pattern distortion. Storage container panels have large areas, and the melt flow path inside the cavity is long, making flow-front unevenness more pronounced.
Shrinkage rate mismatch between label and substrate
When the shrinkage rate of the label material does not match that of the storage container's PP substrate, the two shrink asynchronously after injection cooling, and the pattern is pulled out of shape. Label material selection must match the container material – PP containers with PP labels is the safest approach.
Improper gate position
An unreasonable gate position causes uneven melt flow inside the cavity, with local flow rates too fast or too slow, generating uneven shear forces on the film and causing pattern deformation.
| Investigation Direction | Specific Measures |
|---|---|
| Film forming | Control thermoforming stretch ratio; avoid over-stretching |
| Material matching | Use the same PP material for label and container to ensure consistent shrinkage rates |
| Gate design | Optimize gate position; use multi-point or fan gates for uniform melt flow |
| Injection parameters | Use multi-stage injection control to avoid sudden changes in melt flow velocity |
The label edges separate and lift away from the storage container body. In severe cases, the entire label can be peeled off from the container. This is a typical manifestation of adhesion failure.
Material compatibility issues
Insufficient compatibility between the label material and the plastic substrate is the root cause of delamination. If the label material's melting point, shrinkage rate, thermal expansion coefficient, etc., do not match the substrate, delamination or peeling is likely to occur during injection.
Mold design defects
Poor venting, uneven cooling, or inaccurate label positioning in the mold can lead to insufficient bonding between the label and substrate. Blocked venting traps gases, forming bubbles that affect bonding.
Inappropriate injection molding process parameters
Unreasonable settings of injection temperature, pressure, speed, etc., can result in insufficient bonding. Excessively high temperature softens or even melts the label material; excessively low temperature results in inadequate bonding.
Inadequate label surface treatment
If the label surface has not been properly pre-treated (e.g., corona treatment), adhesion to the plastic substrate may be insufficient. Contaminants such as oil and dust on the label surface also affect bonding.
| Investigation Direction | Specific Measures |
|---|---|
| Material matching | PP substrate with PP labels; ensure melting point, shrinkage rate, and thermal expansion coefficient match |
| Mold venting | Optimize the venting system to ensure smooth gas evacuation and prevent bubble formation |
| Cooling system | Design a uniform cooling system to ensure even temperature distribution in the bonding area |
| Injection parameters | Set temperature, pressure, and speed appropriately; control holding pressure and cooling time |
| Surface treatment | Perform corona treatment on the label surface to increase surface energy and enhance adhesion |
When quality issues arise in IML storage container production, it is recommended to troubleshoot systematically in the following order:
Step 1: Check incoming label materials (Label Selection)
Step 2: Check workshop environment (Temperature/Humidity)
Step 3: Check injection parameters (Process)
Step 4: Check mold structure (Hardware)