Location:
Two-Tone Plastic Tables and Chairs – How Should IML In-Mold Labels Be Designed and Laid Out to Balance Aesthetics and Molding Stability?
Tech & News

Two-Tone Plastic Tables and Chairs – How Should IML In-Mold Labels Be Designed and Laid Out to Balance Aesthetics and Molding Stability?

Two-Tone Plastic Tables and Chairs – How Should IML In-Mold Labels Be Designed and Laid Out to Balance Aesthetics and Molding Stability?

Two-tone plastic tables and chairs have become increasingly popular in the outdoor leisure furniture market in recent years – one color for the base, another for the seat surface, or two colors spliced together for a striking contrast effect – creating rich visual layers and a strong sense of design.

However, the combination of two-shot injection molding and IML in-mold labeling imposes higher demands on label design and layout. Place the label in the wrong position or overlook a single process detail, and at best the pattern gets cut off by a weld line; at worst, the entire batch is scrapped.

This article combines the process characteristics of two-shot injection molding to explain IML label design and layout rules for two-tone plastic tables and chairs from two core dimensions: keeping labels away from weld lines and properly reserving shrinkage allowances. It helps designers ensure both aesthetically pleasing LOGO patterns and significantly reduced injection molding scrap rates.

📖 Table of Contents

1. Two-Shot Injection Molding: The "Double Challenge" for IML Labels

Furniture-4.jpg

What is two-shot injection molding?

Two-shot injection molding is a method in which an injection molding machine equipped with two or more injection systems injects different types or colors of plastic into the mold simultaneously or sequentially. The common approach is: inject the first color of plastic (first shot), rotate the mold 180°, then inject the second color of plastic (second shot).

Two key process characteristics of two-shot injection molding directly affect IML label design and layout:

First, weld lines exist. During two-shot injection molding, when molten plastic flows through the cavity, if two melt streams fail to fully fuse at their meeting interface, visible streaks or linear marks will form on the product surface. Weld lines always form in the direction of melt flow. If a label happens to cover the weld line area, the pattern will be "cut off" – an unsightly and permanent line mark appearing in the middle of the LOGO.

Second, shrinkage is more complex. The shrinkage rate of a two-shot mold depends on the first-shot material, and the second-shot material must have the same shrinkage rate as the first. If the shrinkage rates of the two materials differ, the product will develop "steps" – a noticeable ridge at the junction of the two colors. IML labels themselves also have a shrinkage rate (typically around 0.3% for IML products), and the label material must have a shrinkage rate close to that of the product. In two-shot products, this matching relationship is even more complex – the label must not only match the first shot but also accommodate the shrinkage of the second shot.

It is precisely because of these two process characteristics that IML label design and layout for two-tone plastic tables and chairs must follow a set of rules different from those for single-color injection molding.

2. Rule 1: Labels Must Avoid Weld Lines

This is the most important rule in designing two-shot IML products.

Where do weld lines occur?

Weld lines form where melt streams split and then rejoin. In two-shot injection molding, weld lines typically occur:

  • Where plastic flows around cores or inserts and then rejoins
  • Where melt streams meet when multiple gates are used
  • At junctions where wall thickness changes

Why must labels avoid weld lines?

A weld line is essentially a "seam" where two melt streams failed to fully fuse. At the weld line, the molecular chains of the plastic are not fully interwoven, resulting in lower strength and density than surrounding areas. If a label covers a weld line:

  • The label may be "torn" by the two melt streams during injection, causing wrinkling or shifting
  • After molding, label adhesion is weaker at the weld line, potentially leading to edge lifting with long-term use
  • The weld line creates an unremovable line mark on the label surface, cutting through the pattern and severely affecting aesthetics

How to determine the weld line location?

During the product and mold design phase, the occurrence and position of weld lines must be predicted. The most reliable method is to use mold flow analysis software (such as Moldflow) for simulation, accurately predicting the location and shape of weld lines by simulating melt flow paths within the cavity.

Design recommendations:

  • During the mold flow analysis stage, clearly mark weld line locations
  • The IML label layout area must avoid weld line zones, maintaining at least a 5-10mm safety distance
  • If complete avoidance is impossible, weld lines should be guided to areas outside the label, or hidden on non-visible surfaces of the product

3. Rule 2: Reserve Enough Allowance for Shrinkage

Shrinkage is the most easily overlooked but most consequential factor in IML label design.

What is the shrinkage rate of IML labels?

IML products have a relatively small shrinkage rate, typically around 0.3%. This is because the label fuses with the plastic during injection, effectively adding a "skeleton" layer on the product surface that restricts free shrinkage of the plastic.

Shrinkage is more complex in two-shot products.

The shrinkage rate of a two-shot mold depends on the first-shot material. The second-shot material must have the same shrinkage rate as the first. If the shrinkage rates differ, the product will develop steps.

For IML labels, the label material must also have a shrinkage rate close to that of the product. In two-shot products, this means the label material must match the shrinkage characteristics of both the first and second shots – if the two materials have significantly different shrinkage rates, the label is likely to wrinkle or delaminate at the two-color junction.

Design recommendations:

  • Label dimensions must be pre-compensated for shrinkage. The developed label size = final product size ÷ (1 - shrinkage rate)
  • In two-shot products, the shrinkage rates of the first and second shot materials must be identical
  • The label material's shrinkage rate must be close to that of the product substrate
  • At the two-color junction, reserve additional shrinkage compensation allowance (recommended 0.5-1mm more than for single-color products)

4. Rule 3: Gate Position Determines Label Layout Direction

IML injection mold gate design differs significantly from ordinary injection molds.

The gate must avoid the label area.

To prevent melt from washing away the ink on the label during injection, IML injection molds should use submarine gates for feeding. If the gate faces the label directly, the high-speed, high-temperature melt will directly impact the label surface – potentially washing away ink, shifting the label, or even burning the label film.

Two-shot injection molding involves two gate systems.

Two-shot injection includes two separate runner systems for the first and second shots. The gate position of the first shot determines the flow direction of the first plastic; the gate position of the second shot determines the flow direction of the second plastic. Neither gate system should face the label area.

Design recommendations:

  • Confirm the positions of both gate systems before designing the label layout
  • The label should be positioned away from all gates
  • If the label area is too large to completely avoid gates, ensure the gate feeds from the side of the label rather than impacting it head-on

5. Rule 4: The "Safety Distance" Between Labels and the Two-Tone Dividing Line

Two-tone plastic tables and chairs have a dividing line between the two colors – the boundary where the two colors meet.

The dividing line is a stress concentration area.

Even if the shrinkage rates of the two materials at the junction are perfectly identical, the microscopic shrinkage behavior still differs slightly due to the different color pigments. These subtle differences create microscopic stress at the dividing line. If a label covers the dividing line:

  • The label experiences opposing stresses on either side of the dividing line, and may crack over time with long-term use
  • Label adhesion is weakest at the dividing line, making it the most likely place for edge lifting
  • If the label pattern crosses the dividing line, the two different color backgrounds visually "compete" with the pattern

Design recommendations:

  • IML labels should not cross the two-tone dividing line
  • Maintain at least a 3-5mm safety distance between the label edge and the dividing line
  • If the label must cross the dividing line (e.g., a LOGO spanning both colors), reserve a wider transition area at the dividing line and use the pattern's own lines to "conceal" the boundary

6. Rule 5: Directional Considerations in Label Layout Itself

IML labels themselves have directionality – the orientation of the label placement in the mold affects molding quality.

The "flow direction" of the label.

During injection, molten plastic has a clear flow direction within the cavity. If the label is placed perpendicular to the melt flow direction, the melt hitting the label is more likely to cause wrinkling or shifting; if placed parallel to the melt flow, the melt can flow "along" the label surface with less impact force.

Two-shot injection molding has two flow directions.

The melt flow directions of the first and second shots may be completely different. The label must accommodate melt flow from both directions – which is far more complex than single-color injection molding.

Design recommendations:

  • When laying out the label, prioritize alignment parallel to the first-shot melt flow direction
  • If the second-shot flow direction is perpendicular to the first, the label should be positioned outside the "convergence zone" of the two flow directions
  • The label's orientation within the mold should be confirmed with the mold engineer during the mold design phase

7. FAQ

Why are two-shot IML products more prone to problems than single-color ones?
Because two-shot injection molding involves two gate systems, two melt flow directions, and two sets of shrinkage parameters. The label must not only accommodate the process conditions of the first shot but also the second shot. If any parameter mismatches at any point, the defect will be visible on the finished product.
Can weld lines be completely eliminated?
No. In two-shot injection molding, weld lines are an unavoidable process phenomenon. What designers can do is not "eliminate" weld lines but "guide" them to locations that do not affect appearance.
Can labels cross the two-tone dividing line?
Not recommended. The dividing line is a stress concentration area, and labels crossing it are prone to edge lifting or cracking. If crossing is unavoidable due to design requirements, a wider transition area must be reserved at the dividing line, and thorough validation should be conducted during the sampling stage.
What does a 0.3% shrinkage rate mean?
It means: a 100mm wide label will shrink approximately 0.3mm (100 × 0.3%) after molding. When designing the label size, you need to calculate backward from the final product dimensions – the developed label size = final product size ÷ (1 - 0.3%).
Must the shrinkage rates of the two materials in a two-shot product be exactly the same?
They must be close. If the shrinkage rates differ, the product will develop "steps" at the two-color junction – one side higher than the other, with a noticeable ridge feel. In IML products, steps can also cause the label to wrinkle or delaminate at the junction.
How can I determine weld line locations without mold flow analysis software?
You can refer to historical experience from similar product structures or consult your mold supplier. However, the most reliable method remains using mold flow analysis software for simulation – this is the current industry standard practice.

Contact Us

  • Name*

  • Telephone*

  • Region*

  • Please fill in your request*

电话咨询:020-000000
QQ咨询:177488228
微信客服
扫码咨询