Location:
IML Label Static Tension Winding and Unwinding Control Process: Solving Label Stretching and Lengthening After Printing and Die-Cutting
Tech & News

IML Label Static Tension Winding and Unwinding Control Process: Solving Label Stretching and Lengthening After Printing and Die-Cutting

IML Label Static Tension Winding and Unwinding Control Process: Solving Label Stretching and Lengthening After Printing and Die-Cutting

In IML (In-Mold Labeling) production, the dimensional accuracy of the label directly determines positioning accuracy during injection molding and the final product's appearance quality. A frequently overlooked but extremely critical factor is tension control.

Improper tension control causes the label to be unidirectionally stretched during printing, slitting, and die-cutting processes, resulting in dimensional changes – labels become longer, wider, or skewed. These tiny dimensional deviations may be only a few tenths of a millimeter on a single label, but when accumulated across an entire roll and then magnified through injection molding, they can lead to labels that cannot be precisely positioned in the mold, pattern shifts, exposed edges, or even entire batch scrappage.

This article provides a systematic explanation of how to solve label stretching and lengthening issues through static tension winding and unwinding control processes in IML label production, covering three dimensions: the principles of tension control, tension settings for each process step, and common problem troubleshooting.

📖 Table of Contents

1. Why Is Tension Control Critical for IML Labels?

crate-1.jpg

The substrate of IML labels is plastic film (primarily PP or PE), not paper. Plastic film has elasticity – it stretches and deforms under stress, and this deformation does not fully recover after the stress is removed.

The typical IML label production process is: printing → slitting → die-cutting → injection molding. Throughout this process, the label film undergoes multiple cycles of winding, unwinding, pulling, and cutting. If tension control is inadequate at any step, the film will be unidirectionally stretched, causing label dimensions to change.

Chain reaction of dimensional deviation:

  • Stretched during printing → pattern lengthens, registration off
  • Stretched during slitting → inconsistent label width
  • Stretched during die-cutting → label shape does not match mold
  • During injection molding → label shifts, wrinkles, or exposes edges in the mold

IML label die-cutting position deviation should not exceed ±0.5mm, and die-cutting dimensional tolerances are subject to clear industry standards. Achieving this precision requires stable, controllable tension throughout the entire process from printing to die-cutting.

2. Sources of Tension in IML Label Production

IML label substrate is film material. During printing, slitting, die-cutting, and other processes, tension mainly comes from the following sources:

Unwinding tension: Resistance from the unwinding shaft as the roll material is pulled out. Excessive tension stretches the film before it even enters the printing unit.

Pulling tension: The pulling force exerted by pull rollers between various process steps. Speed differences between pull points cause tension fluctuations.

Rewinding tension: Tension during finished product winding. Excessive rewinding tension deforms the label material, affecting subsequent die-cutting accuracy.

Printing unit tension: Tension generated by speed differences between color groups during printing, directly affecting registration accuracy.

Difference from pressure-sensitive labels: Compared to pressure-sensitive labels, the unwinding and rewinding tension during in-mold label printing should be considerably lower. This is because IML labels lack a backing paper support, and the film itself has limited tensile strength.

Excessive unwinding tension deforms the in-mold label material, causing registration errors in subsequent printing; excessive rewinding tension deforms the in-mold label material, causing inaccuracies in subsequent die-cutting.

3. Tension Control Points for Each Process Step

3.1 Unwinding Tension – Controlling Stretching at the Source

Unwinding tension is the first checkpoint in tension control.

The direct consequence of excessive unwinding tension: the film is already stretched before entering the printing unit. When the stretched film enters printing, the pattern will lengthen, and this stretching is irreversible – even after printing is complete, the film will not "shrink back."

Control points:

  • Unwinding tension should be set to the minimum value that allows smooth unwinding, with the principle of not stretching the film
  • Use automatic tension controllers that adjust unwinding tension automatically based on roll diameter changes
  • Use ultrasonic web guiding systems to ensure the material does not wander during unwinding

3.2 Printing Tension – Ensuring Registration Accuracy

During printing, the film needs to run smoothly between color groups. If tension fluctuates, registration accuracy cannot be guaranteed.

Control points:

  • Printing presses should be equipped with automatic material tension control devices to maintain uniform tension throughout the paper feed process
  • Use multi-stage tension control – unwinding section, printing section, and rewinding section each have different tension setpoints
  • Use closed-loop tension control systems for real-time monitoring and adjustment
  • UV curing unit heat can also affect film tension – pay attention to matching UV lamp power and speed

3.3 Slitting Tension – Preventing Dimensional Deviation

Slitting is the process of cutting large rolls into narrower rolls that meet requirements. Tension control during slitting directly affects the width consistency of the finished labels.

Control points:

  • Slitting rewinding tension should neither be too loose nor too tight – too loose causes core slippage, too tight stretches and deforms the film
  • Slitting speed and rewinding tension should be synchronously matched
  • Different width slit rolls should have separate tension settings

3.4 Die-Cutting Tension – Ensuring Precise Label Shape

Die-cutting is the final dimensional shaping step in IML label production. Tension control during die-cutting directly determines the label's final shape and dimensions.

Die-cutting equipment needs to complete die-cutting, counting, stacking, and waste winding under tension control.

Control points:

  • Die-cutting unwinding tension should be consistent with printing and slitting processes
  • Waste winding tension needs separate control to prevent waste pulling from affecting label positioning
  • After die-cutting, finished labels should be naturally flat without curling or deformation

4. Common Quality Issues from Improper Tension

Tension IssueDirect ManifestationSubsequent Impact
Excessive unwinding tensionFilm stretched and lengthenedRegistration errors, pattern distortion
Excessive rewinding tensionLabel rolls overwoundDimensional deviation during die-cutting, increased scrap rate
Excessive machine direction tensionLabel curls inwardLabel cannot lie flat against mold during injection
Inconsistent tension across processesDimensional batch variationPositioning errors when loaded into machine
Tension fluctuationsRegistration deviation, die-cutting offsetInconsistent batch dimensions

5. Process Parameter Reference for Static Tension Control

The following parameters are industry reference values. Actual production settings should be adjusted based on film material, thickness, width, and other factors:

Process StepRecommended Tension RangeControl MethodNotes
UnwindingMinimum that does not stretch filmAutomatic tension controllerAutomatically reduces tension as roll diameter decreases
PrintingUniform and stable, consistent across color groupsClosed-loop tension controlMulti-stage independent control
SlittingSlightly lower than printing tensionIndependent tension controlDifferent widths set separately
Die-cuttingConsistent with printing tensionConstant tension controlWaste winding controlled separately

Production environment recommendations:

  • Workshop temperature maintained at around 20°C, relative humidity around 60%
  • Install static eliminators at both the unwinding and rewinding sections of the printing press
  • Where possible, equip the factory with static detectors to monitor static elimination effectiveness

6. FAQ

Q1: Why do IML labels have stricter tension requirements than pressure-sensitive labels?
IML labels lack a backing paper support, and the film itself has limited tensile strength. Excessive tension directly stretches and deforms the film, and this deformation is irreversible. Pressure-sensitive labels have backing paper protection and are more tolerant of tension variations.
Q2: Can a label that has been stretched and lengthened recover?
No. Once plastic film is stretched, the molecular chains become oriented, and even after the force is removed, it will not fully return to its original shape. Therefore, tension control must be done at the source – you cannot rely on subsequent processes to "correct" it.
Q3: How can I tell if unwinding tension is too high?
Check whether longitudinal streaks or edge waviness appear on the film before it enters the printing unit. If these phenomena are present on the film surface, it indicates that unwinding tension has already caused film stretching deformation.
Q4: Should tension be consistent across all process steps?
It should be as consistent as possible, but in actual production, the material condition at each step is different (from large rolls to small rolls, from full width to slit widths). Tension values need to be set separately. The key is smooth transition – tension should not change abruptly from one process to the next.
Q5: What is the relationship between tension control equipment and static elimination?
Static electricity can cause film to stick or adhere during winding and unwinding, leading to tension fluctuations. Static eliminators help maintain stable film running conditions and indirectly assist tension control. Workshop temperature and humidity stability also affect static electricity and tension control.
Q6: Why do die-cut labels curl?
One of the main reasons is excessive machine direction tension. The film is overly stretched before die-cutting, and after die-cutting, stress release causes the label to curl inward. The solution is to correctly adjust and control tension based on ink layer thickness and material thickness.

Contact Us

  • Name*

  • Telephone*

  • Region*

  • Please fill in your request*

电话咨询:020-000000
QQ咨询:177488228
微信客服
扫码咨询