Location:
Flatbed Die‑Cutting in In‑Mould Label Production: A Detailed Overview
Tech & News

Flatbed Die‑Cutting in In‑Mould Label Production: A Detailed Overview

Flatbed Die‑Cutting in In‑Mould Label Production: A Detailed Overview

IML-14.jpg

Among the final converting steps for in‑mould labels (IML), die‑cutting transforms wide printed film into individual labels. Flatbed die‑cutting is the most traditional, fundamental, and lowest‑entry method. With its low tooling cost and intuitive pressure adjustment, it still holds a place in small‑batch production, high‑mix varieties, prototyping, and trial runs. This article comprehensively analyses flatbed die‑cutting technology, covering its working principle, two typical configurations, advantages and disadvantages, application scenarios, and a comparison with rotary die‑cutting.

1. Working Principle: “Punching” Labels Like a Stamping Press

The name “flatbed” comes from its core structure: the die is flat. The die plate (upper flatbed) and the base plate (lower flatbed) move up and down intermittently. When the material enters the gap, the upper bed presses down, the cutting rule cuts completely through the material, then the upper bed lifts, the material advances one step, and the cycle repeats. This is essentially like a mechanical stamping press, hence it is often called “punch die‑cutting”.

Unlike rotary die‑cutting (rolling shear), flatbed die‑cutting is intermittent impact. This operating principle limits its maximum speed but also brings the advantages of simple construction and low tooling cost.

2. Two Typical Configurations

Depending on the material form, flatbed die‑cutting is divided into web‑fed and sheet‑fed.

2.1 Web‑fed Flatbed

This method is used for roll‑fed IML label materials and is an offline process (printing and rewinding first, then die‑cutting separately). The workflow:

  • Intermittent web feed: The material is advanced stepwise by feed rollers. Each step equals the length of one label (plus waste gap).

  • Stop‑and‑cut: When the web stops, the upper flatbed descends, completing one cut.

  • Waste stripping and rewinding: After cutting, the waste skeleton is separated from the finished labels. Waste is typically rewound on a separate shaft, while finished labels fall into a collection box or are conveyed away.

Technical features:

  • Suitable for continuous webs with automatic waste stripping – good for medium batches.

  • Frequent start‑stop requires precise inertia control and tension stability.

  • Typical speed: 20–60 strokes per minute (depending on step length and web width), far lower than rotary.

2.2 Sheet‑fed Flatbed

This method is used for sheet‑fed materials (paper or film sheets) and is also offline. Workflow:

  • Automatic sheet feeding: Stacked sheets are fed one by one into the die‑cutting station via a feeder (with suction cups or friction wheels).

  • Registration and cutting: After the sheet is positioned by front lays and side lays, the upper bed descends to cut.

  • Automatic waste stripping and stacking: After cutting, the finished labels are separated from the waste (by grippers or air jets) and stacked.

Technical features:

  • Suitable for sheet materials, especially thick card or rigid IML materials that cannot be wound.

  • Accuracy is slightly lower than web‑fed flatbed due to sheet feeding tolerances (typically ±0.2–0.5 mm).

  • Quick die change – ideal for short runs with frequent job changes.

3. Advantages of Flatbed Die‑Cutting

3.1 Extremely low tooling cost

Flatbed dies are typically wooden laser‑cut dies (steel rule embedded in plywood) or resin dies. They are simple to make, require no precision machining, and are far cheaper than rotary die cylinders (which can cost thousands of dollars each). For small batches (a few hundred to tens of thousands of labels), flatbed cutting dramatically reduces tooling cost per label, and dies can be re‑sharpened several times.

3.2 Intuitive pressure adjustment – tolerant to material thickness variation

Pressure adjustment on a flatbed cutter is usually via mechanical screw or pneumatic boost. Operators can easily find the correct cutting depth by manual trimming or using a pressure gauge. When material thickness varies (e.g., multi‑layer laminate with ±10 μm deviation), flatbed cutters can locally adjust pressure by adding underlay sheets (called “make‑ready”) – something nearly impossible with rotary dies. Therefore, flatbed cutting is better suited for recycled films or paper‑based IML labels with uneven thickness.

3.3 Fast die change – suitable for small batches and high mix

Flatbed dies are typically held on the upper and lower platens by magnetic or mechanical clamping. Changing a die takes only 5–10 minutes, whereas changing a rotary die cylinder may take 30 minutes or more and requires lifting equipment. Thus, flatbed die‑cutting is excellent for environments with many label designs and small order quantities per design.

4. Disadvantages of Flatbed Die‑Cutting

4.1 Slow speed – low productivity

Because the cutting action is intermittent, the web/sheet must pause after each stroke, severely limiting maximum speed. Typical speeds: web‑fed flatbed 30–80 strokes/minute; sheet‑fed flatbed 20–40 sheets/minute. In contrast, rotary die‑cutting runs continuously at speeds equivalent to 200–400 strokes/minute (in terms of label output). For annual volumes exceeding one million labels, flatbed cutting becomes a bottleneck.

4.2 Moderate cutting accuracy

Accuracy is affected by several factors: intermittent web feed error (typically ±0.5–1 mm), parallelism of die mounting, vibration during stamping, and sheet deformation. Generally, flatbed die‑cutting offers repeatability of ±0.2–0.5 mm, while rotary can achieve ±0.1 mm or better. For IML labels that require precise alignment with printed graphics (e.g., fine borders on clear labels), flatbed cutting may cause off‑cut, increasing reject rates.

4.3 Waste stripping often requires auxiliary or manual help

In flatbed cutting, separation of the waste skeleton from finished labels usually needs auxiliary air blowing, mechanical brushes, or manual picking. Especially for complex label shapes (with small holes or narrow legs), waste tends to cling to finished labels, requiring operator intervention. Rotary die‑cutting, by contrast, uses differential rotation and automatic waste rewind for fully automatic stripping.

4.4 Shorter tool life

Flatbed steel‑rule dies are typically made of high‑carbon steel or chrome steel, which are less hard and wear‑resistant than the tungsten carbide or magnetic sheet dies used in rotary systems. When cutting films containing glass fibre or high filler content, the blades wear quickly, often requiring sharpening or replacement every few tens of thousands of cuts.

5. Typical Application Scenarios in IML

Despite its slower speed and moderate accuracy, flatbed die‑cutting remains irreplaceable in the following situations:

Application ScenarioReason
Prototyping / samplingFast die fabrication (within one day), low cost – ideal for verifying label shape and print registration
Small custom ordersFor exhibition souvenirs, limited‑edition cosmetic labels – batches of a few thousand pieces – flatbed is the most economical
Frequent shape changesExample: lubricant brands changing bottle label designs quarterly – flatbed allows rapid response
Films with large thickness variationE.g., PE+PP composites with high recycled content – flatbed can compensate non‑uniformity via make‑ready
Paper‑based IML labelsPaper has high stiffness but produces dust during cutting – flatbed’s open construction is easier to clean and maintain

6. Comparison: Flatbed vs. Rotary Die‑Cutting

AspectFlatbed Die‑CuttingRotary Die‑Cutting
Speed20–80 strokes/minute200–400+ strokes/minute (continuous)
Tooling costLow (tens to a few hundred CNY)High (thousands to tens of thousands CNY)
Die change time5–10 minutes30–60 minutes
Cutting accuracy±0.2–0.5 mm≤ ±0.1 mm
Material toleranceHigh tolerance to thickness variationRequires uniform material
Waste strippingRequires auxiliary or manualFully automatic
Suitable batch sizeA few thousand to tens of thousandsOver 100,000 pieces
Typical tool lifeTens to hundreds of thousands cutsMillions of cuts

7. Conclusion

Flatbed die‑cutting serves as the “versatile backup solution” in IML processing. With its low cost and high flexibility, it has found a clear niche alongside rotary die‑cutting. For start‑up label converters, sampling centres, and companies serving small‑batch customisation in fast‑moving consumer goods, flatbed cutting remains the most cost‑effective choice. However, as labour costs rise and lead times shrink, more IML producers are shifting core orders to rotary lines, leaving flatbed for prototyping and emergency jobs. Understanding the boundaries of each method helps manufacturers develop the most rational die‑cutting capacity strategy based on their product portfolio.



Contact Us

  • Name*

  • Telephone*

  • Region*

  • Please fill in your request*

电话咨询:020-000000
QQ咨询:177488228
微信客服
扫码咨询