Location:
What Are the Main Materials in In-Mold Label Production?
Tech & News

What Are the Main Materials in In-Mold Label Production?

What Are the Main Materials in In-Mold Label Production? – A Comprehensive Technical Overview from Substrate to Functional Layers

IML-2.jpg

1 Introduction

In-Mold Labeling (IML) is a technology where a printed label is placed inside an injection or blow mold and then fused with the molten resin during the molding process, resulting in a label that is integrally bonded to the container surface. Compared with traditional self-adhesive labels or direct screen printing, IML offers significant advantages such as no bubbles, never peeling off, high scratch resistance, and recyclability. It is widely used in daily chemicals, food, pharmaceuticals, and automotive interior trim.

In IML production, materials are the core of the technology. A high‑performance IML label is not simply “a printed film” but a multi‑layer functional system consisting of a substrate layer, an adhesive layer, an ink layer, and protective coatings. This article systematically reviews the main materials used in IML from a technical perspective, analyzes material selection logic, key parameters, and the latest trends, and presents the information with the aid of figures and tables.


2 Overall Material Architecture of an IML Label

A typical IML label consists of four functional layers, as shown in the schematic below:

Figure 1 – Schematic diagram of a typical IML layer structure

(From top to bottom):

  • Topcoat / protective layer (UV varnish – scratch and chemical resistance)

  • Ink layer (UV ink – forms the graphic)

  • Top substrate (BOPP/PE – carries the printing)

  • Core support layer (PP/PE coextruded layer – provides stiffness)

  • Adhesive layer (hot‑melt resin – fuses to the container during molding)

Note: Actual layer counts can range from 3 to 7 depending on the process.

Total label thickness is typically between 50 and 120 μm. The following table summarizes the main materials and functions of each layer.

LayerTypical MaterialsCore Function
Topcoat / protective layerUV/EB cured varnishWear resistance, chemical resistance, gloss enhancement
Ink layerUV curable inkForms the printed image
Top substrateBOPP, PECarries the ink, provides a print surface
Core support layerPP, PE, multilayer coextrusionProvides stiffness, heat resistance, dimensional stability
Adhesive layerAPAO, EVA, functionalized polyolefinMelts during molding and bonds to the container wall

3 Substrate Layer – The “Skeleton” of the Label

The substrate is the most important structural material of an IML label. It determines the stiffness, thermal stability, transparency, and compatibility with the container.

3.1 Comparison of Mainstream Substrates: BOPP vs PE vs Multilayer Coextruded Film

PropertyBOPPPEPP+PE Multilayer Coextrusion
Stiffness★★★★★★★★★★★
Transparency★★★★★★★★★★★
Heat resistance (heat deflection temp.)~100°C~60°C~85°C
Fusion compatibility with PE containersPoor (needs tie layer)ExcellentExcellent
Fusion compatibility with PP containersExcellentPoorExcellent
Typical thickness (μm)50–8060–12050–90
Cost levelMediumLowMedium‑high

Table 1 – Performance comparison of three mainstream substrates

3.1.1 BOPP (Biaxially Oriented Polypropylene)

BOPP is produced by biaxial orientation, which aligns the molecular chains and increases crystallinity, resulting in extremely high stiffness and transparency. Its surface energy can be raised to above 42 dyn/cm by corona treatment, giving excellent printability. The main drawback is insufficient direct thermal fusion compatibility with PE containers, which often requires an additional PE tie‑layer.

Typical applications: cosmetic bottles, high‑grade food containers, daily chemical packaging (with PP containers).

3.1.2 PE (Polyethylene)

The main advantage of PE substrate is perfect chemical compatibility with PE blow‑molded bottles, enabling mono‑material recycling. However, its low stiffness makes it prone to deformation during high‑speed printing or high‑temperature molding; therefore, it is mainly used for low‑demand thin‑wall containers.

Typical applications: detergent bottles, shampoo bottles (HDPE/LDPE bottles).

3.1.3 Multilayer Coextruded Film

This is the current mainstream technology for high‑end IML labels. By coextruding different functional resins (PP, PE, EVA, EVOH, etc.) in one pass, a label with precisely partitioned properties can be produced. For example:

  • Top layer: BOPP or high‑gloss PP – excellent printing surface.

  • Core layer: PP or filled PP – stiffness and low shrinkage.

  • Sealant layer: modified PE or APAO – good fusion to the container.

Figure 2 – Cross‑section illustration of a five‑layer coextruded IML film

(Color‑coded layers showing each resin type and thickness ratio)


4 Adhesive Layer – The Key to Fusion Quality

The adhesive layer sits at the very bottom of the label. During molding, it melts under high temperature and pressure and “welds” the label to the container surface. It is not a conventional pressure‑sensitive adhesive, but a heat‑activated bonding resin.

4.1 Mainstream Adhesive Material: Amorphous Poly‑alpha‑olefin (APAO/APO)

APAO is a family of non‑crystalline thermoplastic polymers obtained by copolymerizing propylene, butene, and ethylene. It features low softening points, high adhesion strength, and excellent compatibility with polyolefins. Major global suppliers include Eastman (Eastoflex™ series), REXtac, Huntsman, etc.

4.2 Key Parameters and Selection Criteria

ParameterMeaningTypical rangeImpact on process
Softening point (R&B)Temperature at which adhesive starts to melt120–155 °CMust match mold temperature (injection molds typically 160–220 °C; blow molds lower)
Melt viscosity (at 190°C)Melt flowability300–20000 cPLow viscosity → easier uniform coating; high viscosity → thicker coats
Glass transition temperature TgIndicator of low‑temperature brittleness-30 °C to -10 °CLower Tg keeps the label flexible and tacky at low temperatures
Tensile strengthCohesive strength of the bond0.5–2 MPaAffects peel resistance of the label

Table 2 – Key parameters of adhesive materials

4.3 Surface Texture Design: Flat vs Engraved

The adhesive layer can be given a micro‑texture to help air escape during molding:

  • Flat (non‑engraved) – suitable for small labels (<30 mm), where natural air release is sufficient.

  • Engraved / grid pattern – mandatory for large labels. Groove depth is typically 5–20 μm, width 0.2–1 mm. During injection, air escapes along the grooves, preventing trapped bubbles.

Figure 3 – Micrograph of an engraved adhesive layer surface and schematic of air release principle


5 Inks and Coatings – Determining Visual Quality and Durability

5.1 Comparison of Ink Systems

TypeCuring mechanismVOCChemical resistanceScratch resistanceCuring speedApplicable processesMarket share
UV curable inkUV‑induced photopolymerizationNoneExcellentExcellentInstant (<0.5 s)Offset, screen, flexo>80%
Solvent‑based inkSolvent evaporation + oxidationHighMediumMediumSlow (minutes)Gravure, flexo<15%
Water‑based inkWater evaporation + film formationVery lowPoorPoorSlowFlexo (niche)<5%

Table 3 – Comparison of ink systems for IML applications

From both performance and productivity standpoints, UV curable inks are the absolute mainstream for IML. They can withstand the high mold temperatures (brief contact above 200 °C) while maintaining colour stability.

5.2 Coating Technologies

5.2.1 Primer

For PE or other low‑surface‑energy substrates, even corona treatment may not provide sufficient ink adhesion. In such cases, a water‑based or solvent‑based primer (only 1–3 μm thick) can be applied, greatly improving ink anchorage.

5.2.2 Overprint Varnish (OPV)

After printing, a UV varnish or EB (electron beam) curable varnish (5–10 μm thick) is usually applied over the graphics. Its functions include:

  • Enhancing scratch and abrasion resistance;

  • Improving chemical resistance (detergents, oils, alcohol);

  • Providing a matte, gloss, or soft‑touch effect.

5.2.3 In‑Mold Decoration (IMD) – Coating‑free technology

Some advanced multilayer coextruded films (e.g., ETFE, FEP, or special BOPP) can integrate the decorative layer directly during coextrusion (e.g., by dispersing pigments in one of the resin layers), eliminating the separate printing step. This technology is called In‑Mold Decoration (IMD), and it is environmentally friendly and suitable for extremely durable applications such as automotive instrument panels.


6 Functional Additives and Sustainable Innovations

6.1 Thinner Gauge Trend

Label thickness has been reduced from over 120 μm in the past to 50–70 μm today, with 45 μm products already available. Thinner labels mean:

  • 30–50% less material consumption per square metre;

  • Shorter injection cycles (the hot‑melt adhesive layer melts faster);

  • Lightweight packaging and reduced carbon footprint.

6.2 Mono‑material Closed‑loop Recycling

Traditional IML labels might use a PP label on a PE container, requiring separation during recycling. To solve this, the industry is strongly promoting mono‑material systems:

  • All‑PP system: PP substrate + PP‑modified adhesive layer + PP container → whole body remelted and reprocessed together.

  • All‑PE system: similar approach, already applied in HDPE packaging.

Figure 4 – Diagram of mono‑material IML closed‑loop recycling process

(Showing the cycle: used container → shredding/washing → melt granulation → remake into new labels/containers)

6.3 Bio‑based and Biodegradable Materials

Although not yet mainstream, some research has been conducted using polylactic acid (PLA) for IML labels in combination with PLA containers to achieve industrial compostability. The main challenge is PLA’s relatively low heat resistance (heat deflection temperature around 55 °C), which can cause deformation during high‑temperature injection molding.

6.4 Smart Label Functionalities

By incorporating functional materials, IML labels can offer added value:

  • Phosphorescent / fluorescent: using long‑afterglow phosphors or fluorescent dyes for special indications or anti‑counterfeiting.

  • Temperature/time indicators: thermochromic inks can indicate if a product has been exposed to high temperatures.

  • RFID/NFC inlays: embedding an ultra‑thin antenna and chip between the label layers for wireless identification.


7 Summary of Material‑Process Matching

Different types of IML applications place emphasis on different material properties. The following table summarizes the typical correlations between applications and material selection.

ApplicationContainer materialMolding processRecommended substrateRecommended adhesiveKey performance requirement
Thin‑wall ice‑cream tubPPInjectionBOPPLow‑softening‑point APAOHigh stiffness, no curling after demolding
Shampoo bottleHDPEBlowPE or multilayer PE/PPPE‑based heat sealSame material as bottle for recyclability
Motor oil containerHDPEBlowMultilayer HDPE/EVOHHigh‑peel‑strength adhesiveOil and chemical resistance
Cosmetic jarPP/PEInjectionHigh‑clarity BOPPHigh‑transparency adhesiveUltimate clarity, no orange peel
Automotive buttonPC/ABSInjectionPC or PET filmSpecial hot‑melt adhesiveHeat resistance, scratch resistance, good feel

Table 4 – Material selection reference for different applications


8 Conclusions and Outlook

The material system of IML labels has evolved from a simple plastic film into a multi‑component, multi‑layer, functionally partitioned composite material. The substrate provides the mechanical skeleton, the adhesive layer ensures thermal fusion, the inks and coatings contribute to visual quality and protection, and functional materials extend the label’s added value.

Three major directions of current technological development are very clear:

  1. Thinner – saving resources and increasing productivity;

  2. Purer – mono‑material systems enabling true closed‑loop recycling;

  3. Smarter – integrating indicators, anti‑counterfeiting, wireless communication, etc.

For both IML manufacturers and end users, understanding the mutual constraints among materials (e.g., how substrate heat resistance influences adhesive choice, or how ink chemical resistance must match the container contents) is the key to successfully developing high‑performance IML products.

Contact Us

  • Name*

  • Telephone*

  • Region*

  • Please fill in your request*

电话咨询:020-000000
QQ咨询:177488228
微信客服
扫码咨询