Location:
Common Production Defects of In-Mold Labels for Storage Containers: Causes and Solutions
Tech & News

Common Production Defects of In-Mold Labels for Storage Containers: Causes and Solutions

Common Production Defects of In-Mold Labels for Storage Containers: Causes and Solutions

Storage containers are typical "large-area, thin-wall, high-frequency-use" plastic products. The application of IML (In-Mold Labeling) labels on storage containers demands higher production process requirements than ordinary small containers – the label area is large, the container body has thin walls, and the injection molding cycle is longer. Any issue at any step means the entire panel is scrapped, resulting in losses far greater than for small-label products.

This article systematically analyzes the five most common defects in IML storage container production from four perspectives: label selection, workshop temperature/humidity, injection molding parameters, and ink compatibility – along with their solutions.

📖 Table of Contents

1. Label Wrinkling – The Most Visible Appearance Defect

Cabinet-IML-27.jpg

1.1 Phenomenon Description

Wave-like wrinkles, localized bulges, or indentations appear on the label surface. In severe cases, the label separates from the container surface. This is one of the most common appearance defects in IML production.

1.2 Cause Analysis

Label dimensions do not match the mold

If the label unit length is too long, it exceeds the reserved space, causing the label to "bunch up" inside the mold; if it is too short, it cannot conform fully to the cavity wall, also causing wrinkles. Storage container labels have large areas, so the amplification effect of dimensional deviations is more pronounced.

Insufficient label material extensibility

Film materials, especially those that can stretch and deform, can conform to the curved surfaces of storage container bodies without wrinkling. If a film with excessive rigidity or insufficient extensibility is chosen, wrinkling is likely to occur on large flat or micro-curved container surfaces.

Electrostatic adsorption failure

IML injection molding generally uses electrostatic label attraction, because injection molding pressure is high and vacuum suction can easily be broken through. If electrostatic adsorption is insufficient, the label cannot firmly adhere to the mold cavity wall and is prone to shifting or wrinkling under the high-pressure, high-temperature impact of injection. Electrostatic performance is significantly affected by humidity – fluctuations in workshop humidity directly cause unstable adsorption.

Inadequate film thermoforming

The film must undergo thermoforming treatment before being placed in the mold. Improper temperature control can cause film deformation and increase the rejection rate. The film size should be 0.02-0.03mm smaller per side than the final part size, ensuring easy placement while allowing full expansion during injection.

1.3 Solutions

Investigation DirectionSpecific Measures
Label dimensionsConfirm label cutting dimensions precisely match the mold cavity; check unit length stability
Label materialChoose a film material with good extensibility; avoid excessive rigidity
Electrostatic adsorptionCheck if the electrostatic generator is working properly; control workshop humidity at around 50%
Film thermoformingStrictly control thermoforming temperature; film size 0.02-0.03mm smaller per side than the part

2. Localized Whitening – Stress Projected on the Surface

2.1 Phenomenon Description

White patches or hazy areas appear on the label area of storage container panels, with the color turning white or grey, creating an obvious color difference from surrounding normal areas. This is often referred to as "blushing" or "stress whitening" in the industry.

2.2 Cause Analysis

Residual stress causing whitening

During demolding, if the draft angle is too small or the mold surface is rough, excessive ejection force creates stress on the product surface. In severe cases, whitening or cracking occurs in stress-concentrated areas. Large flat storage container panels have large surface areas where stress distribution is even more uneven, increasing the risk of whitening.

Uneven wall thickness causing stress concentration

If the wall thickness of storage container panels is uneven – thick areas cool slowly and shrink more – tensile stress is generated at the label-substrate interface, leading to localized whitening. Areas where wall thickness changes are high-risk zones for whitening.

Excessively low mold temperature

Low mold temperature can easily cause product deformation or defects such as white streaks and black spots. For large flat storage containers, localized "cold material" caused by uneven mold temperature is particularly common.

2.3 Solutions

Investigation DirectionSpecific Measures
Mold temperatureIncrease mold temperature to the recommended range; ensure uniform temperature across all cavity areas
Wall thickness designCheck if panel wall thickness is uniform; avoid localized excessive thickness; design smooth transitions at thick-thin junctions
Draft angleCheck if draft angle is sufficient (IML products require ≥3°)
Injection pressureAdjust injection pressure and holding pressure to reduce residual stress

3. Ink Migration – "What Shouldn't Move, Moved"

3.1 Phenomenon Description

After injection molding, the ink on the label shows diffusion, blurring, or darkening of colors. In severe cases, pattern edges become indistinct and color saturation noticeably decreases.

3.2 Cause Analysis

Insufficient ink adhesion to the film

Poor ink adhesion to the label can easily cause ink contamination of the mold, leading to poor product quality. If ink adhesion to the film is insufficient, the high-temperature, high-pressure environment during injection accelerates ink diffusion and migration.

Insufficient ink heat resistance

The temperature of molten plastic during injection can reach 180-280°C. If the ink's temperature resistance limit is lower than the injection temperature, the ink layer softens at high temperatures, and pigment molecules gain enough energy to move within the film.

Additive migration in ink

When the ink or substrate contains excessive plasticizers or other additives, these additives can dissolve some of the ink's pigments under high temperature or long-term storage conditions, causing them to move within the film.

3.3 Solutions

Investigation DirectionSpecific Measures
Ink selectionChoose UV inks – their ink layer strength is higher than solvent-based inks, making them more suitable for in-mold labels
Surface tensionCheck if material surface tension meets requirements (38 dynes); if not, perform corona treatment
Ink testingTest ink adhesion, scratch resistance, and chemical resistance on the label material before use
Additive controlChoose plasticizer additives with low or non-migrating properties; use resins with high softening points as ink binders

4. Pattern Distortion – When Dimensions Change, the Pattern Changes Too

4.1 Phenomenon Description

After injection molding, the pattern on the label appears deformed – circles become ellipses, squares become rectangles, text is stretched or compressed. The pattern clearly does not match the design artwork.

4.2 Cause Analysis

Film stretched and deformed inside the mold

After the IML film is placed in the mold, if the stretch ratio during thermoforming is not properly controlled, or if the melt flow during injection is uneven, the film will be stretched, causing pattern distortion. Storage container panels have large areas, and the melt flow path inside the cavity is long, making flow-front unevenness more pronounced.

Shrinkage rate mismatch between label and substrate

When the shrinkage rate of the label material does not match that of the storage container's PP substrate, the two shrink asynchronously after injection cooling, and the pattern is pulled out of shape. Label material selection must match the container material – PP containers with PP labels is the safest approach.

Improper gate position

An unreasonable gate position causes uneven melt flow inside the cavity, with local flow rates too fast or too slow, generating uneven shear forces on the film and causing pattern deformation.

4.3 Solutions

Investigation DirectionSpecific Measures
Film formingControl thermoforming stretch ratio; avoid over-stretching
Material matchingUse the same PP material for label and container to ensure consistent shrinkage rates
Gate designOptimize gate position; use multi-point or fan gates for uniform melt flow
Injection parametersUse multi-stage injection control to avoid sudden changes in melt flow velocity

5. Edge Delamination – The End Signal of Adhesion Failure

5.1 Phenomenon Description

The label edges separate and lift away from the storage container body. In severe cases, the entire label can be peeled off from the container. This is a typical manifestation of adhesion failure.

5.2 Cause Analysis

Material compatibility issues

Insufficient compatibility between the label material and the plastic substrate is the root cause of delamination. If the label material's melting point, shrinkage rate, thermal expansion coefficient, etc., do not match the substrate, delamination or peeling is likely to occur during injection.

Mold design defects

Poor venting, uneven cooling, or inaccurate label positioning in the mold can lead to insufficient bonding between the label and substrate. Blocked venting traps gases, forming bubbles that affect bonding.

Inappropriate injection molding process parameters

Unreasonable settings of injection temperature, pressure, speed, etc., can result in insufficient bonding. Excessively high temperature softens or even melts the label material; excessively low temperature results in inadequate bonding.

Inadequate label surface treatment

If the label surface has not been properly pre-treated (e.g., corona treatment), adhesion to the plastic substrate may be insufficient. Contaminants such as oil and dust on the label surface also affect bonding.

5.3 Solutions

Investigation DirectionSpecific Measures
Material matchingPP substrate with PP labels; ensure melting point, shrinkage rate, and thermal expansion coefficient match
Mold ventingOptimize the venting system to ensure smooth gas evacuation and prevent bubble formation
Cooling systemDesign a uniform cooling system to ensure even temperature distribution in the bonding area
Injection parametersSet temperature, pressure, and speed appropriately; control holding pressure and cooling time
Surface treatmentPerform corona treatment on the label surface to increase surface energy and enhance adhesion

6. Systematic Troubleshooting in Four Directions

When quality issues arise in IML storage container production, it is recommended to troubleshoot systematically in the following order:

Step 1: Check incoming label materials (Label Selection)

  • Do label dimensions match the mold?
  • Is the label material consistent with the container material (PP with PP)?
  • Is the film extensibility sufficient?
  • Have the inks been tested for adhesion and heat resistance?

Step 2: Check workshop environment (Temperature/Humidity)

  • Is printing workshop temperature at 20-30°C and relative humidity 45-55%?
  • Is injection workshop humidity stable at around 50%?
  • Are labels stored in a moisture-proof and static-proof environment?

Step 3: Check injection parameters (Process)

  • Is mold temperature uniform? Are there localized high or low spots?
  • Are injection pressure, speed, and holding time reasonable?
  • Is the cooling system uniform?

Step 4: Check mold structure (Hardware)

  • Is the venting system unobstructed?
  • Is the draft angle ≥3°?
  • Is the gate position reasonable?
  • Is the electrostatic adsorption system working properly?

7. FAQ

What is the most likely cause of IML label wrinkling?
The most likely causes are label dimensions not matching the mold or electrostatic adsorption failure. First check if label cutting dimensions match the mold cavity, then check if the electrostatic generator is working properly and if workshop humidity is around 50%.
White patches on the label surface – material issue or process issue?
Usually a process issue. Low mold temperature, uneven wall thickness causing excessive residual stress, etc., can all cause whitening. First check if mold temperature is uniform, then investigate wall thickness design and injection pressure.
Are ink migration and ink peeling the same thing?
No. Ink migration is the diffusion and movement of pigments or additives within the film, causing pattern blurring. Ink peeling is the separation of the ink layer from the film. The former is molecular-level diffusion; the latter is interfacial adhesion failure.
What ink should be chosen for IML labels on storage containers?
UV inks are recommended. UV inks have higher ink layer strength than solvent-based inks, making them more suitable for the high-temperature, high-pressure environment of in-mold labeling during injection. Be sure to test the ink's adhesion, scratch resistance, and chemical resistance on the label material before use.
Why must the label material be consistent with the container material?
Because shrinkage rates and thermal expansion coefficients must match. If the label and container materials differ, they shrink asynchronously after injection cooling, causing wrinkling, deformation, or even delamination. PP containers with PP labels is the safest approach.
How much does workshop humidity affect IML quality?
Significantly. Electrostatic adsorption is notably affected by humidity – too low humidity makes static generation difficult, preventing the label from firmly adhering to the mold cavity wall; too high humidity causes static leakage, equally affecting adsorption. The printing workshop is recommended at 20-30°C, 45-55% RH, and the injection workshop at around 50% humidity.
Can IML label edge delamination be repaired?
No. IML labels fuse with the container during injection molding – edge delamination means the interface bonding has already failed and cannot be repaired non-destructively; the product can only be scrapped. Therefore, pre-production parameter debugging and process control are critical.

Contact Us

  • Name*

  • Telephone*

  • Region*

  • Please fill in your request*

电话咨询:020-000000
QQ咨询:177488228
微信客服
扫码咨询