Two-tone plastic tables and chairs have become increasingly popular in the outdoor leisure furniture market in recent years – one color for the base, another for the seat surface, or two colors spliced together for a striking contrast effect – creating rich visual layers and a strong sense of design.
However, the combination of two-shot injection molding and IML in-mold labeling imposes higher demands on label design and layout. Place the label in the wrong position or overlook a single process detail, and at best the pattern gets cut off by a weld line; at worst, the entire batch is scrapped.
This article combines the process characteristics of two-shot injection molding to explain IML label design and layout rules for two-tone plastic tables and chairs from two core dimensions: keeping labels away from weld lines and properly reserving shrinkage allowances. It helps designers ensure both aesthetically pleasing LOGO patterns and significantly reduced injection molding scrap rates.

What is two-shot injection molding?
Two-shot injection molding is a method in which an injection molding machine equipped with two or more injection systems injects different types or colors of plastic into the mold simultaneously or sequentially. The common approach is: inject the first color of plastic (first shot), rotate the mold 180°, then inject the second color of plastic (second shot).
Two key process characteristics of two-shot injection molding directly affect IML label design and layout:
First, weld lines exist. During two-shot injection molding, when molten plastic flows through the cavity, if two melt streams fail to fully fuse at their meeting interface, visible streaks or linear marks will form on the product surface. Weld lines always form in the direction of melt flow. If a label happens to cover the weld line area, the pattern will be "cut off" – an unsightly and permanent line mark appearing in the middle of the LOGO.
Second, shrinkage is more complex. The shrinkage rate of a two-shot mold depends on the first-shot material, and the second-shot material must have the same shrinkage rate as the first. If the shrinkage rates of the two materials differ, the product will develop "steps" – a noticeable ridge at the junction of the two colors. IML labels themselves also have a shrinkage rate (typically around 0.3% for IML products), and the label material must have a shrinkage rate close to that of the product. In two-shot products, this matching relationship is even more complex – the label must not only match the first shot but also accommodate the shrinkage of the second shot.
It is precisely because of these two process characteristics that IML label design and layout for two-tone plastic tables and chairs must follow a set of rules different from those for single-color injection molding.
This is the most important rule in designing two-shot IML products.
Where do weld lines occur?
Weld lines form where melt streams split and then rejoin. In two-shot injection molding, weld lines typically occur:
Why must labels avoid weld lines?
A weld line is essentially a "seam" where two melt streams failed to fully fuse. At the weld line, the molecular chains of the plastic are not fully interwoven, resulting in lower strength and density than surrounding areas. If a label covers a weld line:
How to determine the weld line location?
During the product and mold design phase, the occurrence and position of weld lines must be predicted. The most reliable method is to use mold flow analysis software (such as Moldflow) for simulation, accurately predicting the location and shape of weld lines by simulating melt flow paths within the cavity.
Design recommendations:
Shrinkage is the most easily overlooked but most consequential factor in IML label design.
What is the shrinkage rate of IML labels?
IML products have a relatively small shrinkage rate, typically around 0.3%. This is because the label fuses with the plastic during injection, effectively adding a "skeleton" layer on the product surface that restricts free shrinkage of the plastic.
Shrinkage is more complex in two-shot products.
The shrinkage rate of a two-shot mold depends on the first-shot material. The second-shot material must have the same shrinkage rate as the first. If the shrinkage rates differ, the product will develop steps.
For IML labels, the label material must also have a shrinkage rate close to that of the product. In two-shot products, this means the label material must match the shrinkage characteristics of both the first and second shots – if the two materials have significantly different shrinkage rates, the label is likely to wrinkle or delaminate at the two-color junction.
Design recommendations:
IML injection mold gate design differs significantly from ordinary injection molds.
The gate must avoid the label area.
To prevent melt from washing away the ink on the label during injection, IML injection molds should use submarine gates for feeding. If the gate faces the label directly, the high-speed, high-temperature melt will directly impact the label surface – potentially washing away ink, shifting the label, or even burning the label film.
Two-shot injection molding involves two gate systems.
Two-shot injection includes two separate runner systems for the first and second shots. The gate position of the first shot determines the flow direction of the first plastic; the gate position of the second shot determines the flow direction of the second plastic. Neither gate system should face the label area.
Design recommendations:
Two-tone plastic tables and chairs have a dividing line between the two colors – the boundary where the two colors meet.
The dividing line is a stress concentration area.
Even if the shrinkage rates of the two materials at the junction are perfectly identical, the microscopic shrinkage behavior still differs slightly due to the different color pigments. These subtle differences create microscopic stress at the dividing line. If a label covers the dividing line:
Design recommendations:
IML labels themselves have directionality – the orientation of the label placement in the mold affects molding quality.
The "flow direction" of the label.
During injection, molten plastic has a clear flow direction within the cavity. If the label is placed perpendicular to the melt flow direction, the melt hitting the label is more likely to cause wrinkling or shifting; if placed parallel to the melt flow, the melt can flow "along" the label surface with less impact force.
Two-shot injection molding has two flow directions.
The melt flow directions of the first and second shots may be completely different. The label must accommodate melt flow from both directions – which is far more complex than single-color injection molding.
Design recommendations: